Quality Finishes That Last a Lifetime

PREMIUM TWO PACK POLYURETHANE CLEAR WOOD FINISH FOR EXTERIORS

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Silky Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

WoodCoat High Solids Sealer Clear 15 - 20%
WoodCoat Ext.Glossy Clear 30 - 35%
WoodCoat Ext.Silky Matt Clear 25 - 30%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener. Avoid applying in direct sunlight or when the humidity is very high.

Apply 2 to 3 coats of WoodCoat High Solids Sealer clear with an interval of 8 hours between the subsequent coats. Sanding should be done prior to the application of each coat

Sandpaper #220 can be used for the first coat and Sandpaper #400 can be used for the second and third coats

The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood. Apply 2 coats of either WoodCoat Exterior Glossy clear or WoodCoat Exterior Silky Matt clear depending on the requirement. Sand the first coat with Sandpaper #600, after 8 hours of drying

MRF Woodstains Exterior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For exterior applications use Woodstains exterior shades only

PREMIUM TWO PACK POLYURETHANE CLEAR WOOD FINISH FOR INTERIORS

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

WoodCoat High Solids Sealer Clear 15 - 20%
WoodCoat Ext.Glossy Clear 30 - 35%
WoodCoat Ext.Silky Matt Clear 25 - 30%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener. Avoid applying in direct sunlight or when the humidity is very high.

Apply 2 to 3 coats of WoodCoat High Solids Sealer clear with an interval of 8 hours between the subsequent coats. Sanding should be done prior to the application of each coat

Sandpaper #220 can be used for the first coat and Sandpaper #400 can be used for the second and third coats

The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood. Apply 2 coats of either WoodCoat Exterior Glossy clear or WoodCoat Exterior Silky Matt clear depending on the requirement. Sand the first coat with Sandpaper #600, after 8 hours of drying

MRF Woodstains Exterior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For exterior applications use Woodstains exterior shades only

PREMIUM TWO PACK POLYURETHANE CLEAR WOOD FINISH FOR INTERIORS

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes (Clear and Opaque)

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

WoodCoat Ultra Int.Sealer Clear 45 - 50%
WoodCoat Ultra Int.High Gloss Clear 25 - 30%
WoodCoat Ultra Int.Matt Clear 20 - 25%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

Apply 2 to 3 coats of WoodCoat Ultra Interior Sealer clear with an interval of 2 hrs between the subsequent coats. Sanding should be done prior to the application of each coat

Sandpaper #220 can be used for the first coat and Sandpaper #400 can be used for the second and third coats, number of coats of sealer required varies from 2 to 3 depending on the absorption of wood

Apply 2 coats of either WoodCoat Ultra Interior High Gloss Clear / Matt Clear depending on the requirement, with an interval of 5 hrs between subsequent coats. Sanding of the first coat shall be done using Sandpaper #600

MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For Interior applications use Woodstains Interior shades only

Register your purchase details

  • Upload Invoice Copy