Quality Finishes That Last a Lifetime

SINGLE PACK SOLVENT BASED COAT PAINT FOR TERRACES

TeraFix Water Repellent Primer for Terraces

Pack Sizes

  • 4 Ltrs 10 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Lead Content - Less than 90 PPM

Surface Preparation

Ensure that the surface to be coated is clean and free from oil, grease ,dirt and other contamination

Clean thoroughly using a wire brush and then scuff the surface using#SandPaper 80. Ensure that no loose particles are sticking to the surface to be coated

Freshly plastered surface must be allowed to cure completely. The coating process can be started after a minimum period of 30 days

Do not apply if the surface is damp or when the humidity high

Completely remove existing coating, if any to ensure direct adhesion of TeraFix to the surface

Damaged surface should be rectified before applicationof TeraFix

Apply Using

Brush or Roller

Thinning Details

  • Thinner Recommended - 555 Thinner

Thinner Intake 5%

Application Procedure

Mix the base thoroughly prior to application.

Ensure that the surface to be coated is clean and free from oil, grease , dirt and other contamination

Clean thoroughly using a wire brush and then scuff the surface using # Sandpaper 80. Ensure that no loose particles are sticking to the surface to be coated.

Apply one of TERAFIX for regular terrace surfaces . For uneven / highly porous surfaces apply 2 coats of TERAFIX with an interval of 6 - 8 hours between each coat. Sanding of the first coat shall be done using # 220 Sandpaper.

Apply 2 coats of Aquafresh Cool with an interval of 4 to 5 hours between subsequent coats after subjecting TERAFIX to sanding using # 220 Sandpaper.

After completion, allow curing for a minimum period of 72 hrs

WATER BASED ACRYLIC PAINT FOR TERRACES

AquaFresh Cool Paint for Terraces

Pack Sizes

  • 1 Ltr,4 Ltrs,10 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Lead Content - Less than 90 PPM

- Temperature reduction : 5 - 12 ?C depending on the surface temperature *

- * The drop in temperature varies with the temperature of the surroundings, higher the temperature, greater will be the reduction.

- The reduction in temperature is influenced by the wear and tear , the surface of the film undergoes with time.

Surface Preparation

The surface to be coated should be clean, free from dampness and any other contamination.

Clean the surface thoroughly using a wire brush and then sand the surface using # 80 Sandpaper

Clean thoroughly and ensure that no loose particles are sticking to the surface to be coated.

For freshly plastered surfaces , painting can be initiated after a minimum period of 30 days.

Apply Using

  • 1 Ltr

    Brush or Roller

Thinning Details

Potable water 35 - 40%

Application Procedure

Mix the base thoroughly prior to application.

Apply one coat of Aquafresh Primer. After 3 to 4 hrs, mild scuffing of Primer should be done with # 400 Sandpaper.

Apply 2 coats of Aquafresh Cool with an interval of 4 to 5 hours between subsequent coats.

After completion, the coating should be allowed to cure for a minimum period of 72 hrs

TWO PACK POLYURETHANE FINISH FOR GLASS

GlassCoat PU Glass Finish

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- UV Resistance: Not applicablefor translucent shades

Surface Preparation

Clean using Thinner for finish or appropriate cleaning agent and apply the desired Glasscoat Finish as per recommendation

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

GlassCoat Finishes 15 - 20%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

For application details, please refer product data sheet in downloads menu

SINGLE PACK SOLVENT BASED COAT FOR POROUS ROOF TILES

TileGarde

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Lead Content - Less than 90 PPM

Surface Preparation

The tile to be coated should be clean, dry, free from moisture ,dampness and other contamination.

Sand the surface using Emery Paper No. 80 and clean thoroughly so that no loose particles are held to the surface.

Tilegarde - Solvent Based Coat for Porous Roof Tiles - Paint for Roof Tiles | MRF Paints

Tilegarde Paint for Roof - Single Pack Solvent Based Coat for Porous Roof Tiles comes in 1 Ltr, 4 Ltrs and 20 Ltrs pack.

Thinner Recommended

GP Thinner 5 - 10%

Application Procedure

Mix the base thoroughly prior to application. Apply two coats of the desired TileGarde shade / Tile Garde Clear with an interval of 8 hrs between the subsequent coats. Mild sanding of the first coat with Emery paper No. 400 is required before the application of the second coat. Do not apply when the humidity is very high.

TWO PACK EPOXY ANTI-CORROSIVE COAT FOR VARIED INDUSTRIAL APPLICATIONS

Epidec Epoxy Anti-Corrosive Coat

Pack Sizes

  • 500 ml,1 Ltr,4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Corrosion Resistance depending on conditions

Surface Preparation

Mix the base (Part A) thoroughly before the addition of hardener (Part B). Ensure that the hardeneris slowly added to the base in the specified ratio.

Add the recommended thinner after thoroughly mixing the base and hardener. The mixture should be used within its pot life. Ensure a dust free environment during application

Thinning Details

  • Mix the base thoroughly prior to mixing with the hardener

Thinner Recommended

Epoxy Zinc Phosphate Primer Grey/ Dark Grey Thinner 1110 Ep
GMP Epoxy Red Oxide Red Thinner 1110 Ep
Epoxy Primer Oxide Red/ Metal Grey/ Surfacer Grey Thinner 1110 Ep
Epidec Epoxy RTC Primer Grey/ Zinc ph primer Grey Thinner 1110 Ep

Thinner Intake

Epoxy Zinc Phosphate Primer Grey 30 - 35%
Epoxy Zinc Phosphate Primer Dark Grey 15 - 20%
GMP Epoxy Red Oxide Red 15 - 20%
Epoxy Primer Oxide Red/ Metal Grey/ Surfacer Grey 15 - 20%
Epidec Epoxy RTC Primer Grey 3 - 5%
Epidec Epoxy Zinc ph primer Grey 15 - 20%
Epoxy putty - white / Grey 3 - 5%
Epidec Epoxy Matt 10 - 15%
Epidec Epoxy Glossy 15 - 20%
MRF Coal Tar Epoxy 15 - 20%
Epidec Epoxy ROC Black 3 - 5%

Application Procedure

For application details, please refer product data sheet in downloads menu

©2024 MRF Vapocure Paints - All rights reserved

Register your purchase details

  • Upload Invoice Copy