Quality Finishes That Last a Lifetime

ECONOMICAL TWO PACK POLYURETHANE CLEAR WOOD FINISH FOR INTERIORS

FreshWood Interior Wood Paint

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

Freshwood Int.Sealer Clear 10 - 15%
Freshwood Int.Glossy Clear 20 - 25%
Freshwood Int.Matt Clear 8 - 10%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

Apply 2 to 3 coats of FRESHWOOD PU Interior Sealer clear with an interval of 2-3 hrs between subsequent coats. Sanding should be done prior to the application of each coat. The number of coats varies depending on the absorption of wood

#220 Sandpaper can be used for the first coat and #400 Sandpaper can be used for the second and third coats

Apply 2 coats of either FRESHWOOD PU Interior Glossy Clear or Matt Clear depending on the requirement, with an interval of 5 hrs between subsequent coats. Sanding after the 1st coat of top coat needs to done with #600 or #1000 Sandpaper

MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For Interior applications use Woodstains Interior shades only

ECONOMICAL TWO PACK POLYURETHANE CLEAR WOOD FINISH FOR EXTERIORS

FreshWood Exterior Wood Paint

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

Freshwood Ext.Sealer Clear 15 - 20%
Freshwood Ext.Glossy Clear 15 - 20%
Freshwood Ext.Matt Clear 10 - 15%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

Apply 2 to 3 coats of FRESHWOOD Exterior Sealer clear with an interval of 12 hrs between subsequent coats. Sanding should be done prior to the application of each coat. The number of coats varies depending on the absorption of wood

#220 Sandpaper can be used for the first coat and #400 Sandpaper can be used for the second and third coats

Apply 2 coats of either FRESHWOOD Exterior Glossy Clear or Matt Clear depending on the requirement, with an interval of 12 hrs between subsequent coats. Sanding after the 1st coat of top coat needs to done with #600 or #1000 Sandpaper

MRF Woodstains Exterior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear.

Sanding of the applied shade is not permitted

For exterior applications use Woodstains exterior shades only

ECONOMICAL TWO PACK POLYURETHANE CLEAR WOOD FINISH PAINT COLOUR FOR INTERIORS

TreatWood Interior Wood Paint

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

Treatwood Sealer Clear 35 - 45%
Treatwood Glossy Clear 30 - 35%
Treatwood Matt Clear 20 - 25%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

Apply 2 to 3 coats of Treatwood Sealer clear with an interval of 8 hrs between subsequent coats. Sanding should be done prior to the application of each coat. The number of coats varies depending on the absorption of wood

#220 Sandpaper can be used for the first coat and #400 Sandpaper can be used for the second and third coats

Apply 2 coats of either Treatwood Glossy Clear or Matt Clear depending on the requirement, with an interval of 8 hrs between subsequent coats. Sanding of the 1st coat of top coat shall be done with #600 or #1000 Sandpaper

MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For Interior applications use Woodstains Interior shades only

ECONOMICAL SINGLE PACK POLYURETHANE CLEAR WOOD FINISH FOR INTERIORS AND EXTERIORS

EezeeWood Interior Exterior Wood Paint

Pack Sizes

  • 200 ml,500 ml,1 Ltr,4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Manual Brush Application

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner 3834

EezeeWoodSealer Clear/ Glossy Clear/ Matt Clear 18 - 20% (Interiors),
26 - 32% (Exteriors)

Application Procedure

Mix the base thoroughly prior to application.

Avoid applying in direct sunlight or when the humidity is very high

Apply 2 to 3 coats of EEZEEWOOD XT / Interior Sealer clear with an interval of 12 - 16 hours between the subsequent coats. Sanding should be done prior to the application of each coat. Sandpaper #220 can be used for the first coat and Sandpaper #400 can be used for the second and third coats

The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood

Apply 2 coats of either EEZEEWOOD XT / Interior Glossy Clear or Matt Clear depending on the requirement, with an interval of 12 - 16 hours between the subsequent coats. Sanding of the 1st coat of top coat shall be done with #600 or #1000 Sandpaper

MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For Interior applications use Woodstains Interior shades only

ECONOMICAL TWO PACK POLYURETHANE CLEAR WOOD FINISH PAINT FOR INTERIORS

Melamine Interior Wood Paint

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

This step wise approach makes the surface smooth

Always sand in the direction of the wood grain

Thinning Details

  • Thinner Recommended - Thinner 3830

Melamine Sealer Clear 25 - 30%
Melamine Matt Clear 25 - 30%
Melamine Glossy Clear 25 - 30%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

Apply 2 to 3 coats of Melamine Sealer clear with an interval of 8 hrs between subsequent coats. Sanding should be done prior to the application of each coat. The number of coats varies depending on the absorption of wood

#220 Sandpaper can be used for the first coat and #400 Sandpaper can be used for the second and third coats

Apply 2 coats of either Melamine Glossy Clear or Matt Clear depending on the requirement, with an interval of 8 hrs between subsequent coats. Sanding of the 1st coat of top coat shall be done with #600 or #1000 Sandpaper

MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

For Interior applications use Woodstains Interior shades only

©2024 MRF Vapocure Paints - All rights reserved

Register your purchase details

  • Upload Invoice Copy