EezeeWood 2in 1
Solvent based wood finish
Single pack solvent based Polyurethane clear wood finish for Interiors and Exteriors
DIY Friendly
2-in-1
Available in Glossy and Matt Finishes
Best in Class Finish
Achieve superior quality finishes at an affordable price with our premium economy wood finish.
Stain Resistance
Keep your wooden furniture looking pristine with stain-resistant finish, protecting against oil, water, ink, and food stains.
The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination
For hard wood, sand the surface using sandpaper #80, followed by sandpapers #120, #150, #180 and #220
For Veneer ply surfaces,start with sandpaper #220
Always sand in the direction of the wood grain
Mix the base thoroughly prior to application.
Avoid applying in direct sunlight or when the humidity is very high
Apply 2 to 3 coats of EEZEEWOOD XT / Interior Sealer clear with an interval of 12 – 16 hours between the subsequent coats. Sanding should be done prior to the application of each coat. sandpaper #220 can be used for the first coat and sandpaper #400 can be used for the second and third coats
The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood
Apply 2 coats of either EEZEEWOOD XT / Interior Glossy Clear or Matt Clear depending on the requirement, with an interval of 12 – 16 hours between the subsequent coats. Sanding of the 1st coat of top coat shall be done with #600 or #1000 sandpaper
MRF Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted
For Interior applications use Woodstains Interior shades only
- Manual Brush Application
- Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 – 45 psi
- Thinner Recommended – Thinner 3834
| EezeeWoodSealer Clear/ Glossy Clear/ Matt Clear | 18 – 20% (Interiors), 26 – 32% (Exteriors) |
DOWNLOAD DATA SHEET
Fill the form to access the Data Sheet:
Other Products
About EezeeWood Interior
EezeeWood Interior is MRF Paints’ single-pack (1K) polyurethane clear finish for indoor wood. There is no hardener to mix, so it is DIY friendly and easy to apply by brush or spray, and it gives a clear glossy or matt finish.
The EezeeWood range is 2-in-1: EezeeWood Interior for indoor wood and EezeeWood XT for exterior wood.
Where to use it
- Indoor furniture, rails and wall panelling
- DIY touch-ups and small jobs, as it comes in packs from 200 ml
Key facts
- Single-pack polyurethane clear interior wood finish; no hardener
- Finishes: glossy and matt clear, over EezeeWood Interior Sealer Clear
- Coverage: 75-80 sq ft per litre per coat at 35 microns (data sheet)
- Touch dry in 30 minutes; tack free in 3 hours; hard dry in 72 hours minimum
- Thinner 3834: 18-20%
- Brush or conventional spray; packs of 200 ml, 500 ml, 1 L, 4 L and 20 L
FAQs
Is EezeeWood Interior good for DIY?
Yes. It is a single-pack finish with no hardener to mix, and it can be applied by brush.
How do I apply EezeeWood Interior?
Make sure the wood is clean, dry and free from moisture. For hardwood, sand with #80, then #120, #150, #180 and #220; for veneer ply, start at #220. Always sand along the grain. Apply 2-3 coats of EezeeWood Interior Sealer Clear, 12-16 hours apart, sanding before each coat (#220 first, then #400). Finish with 2 coats of Glossy or Matt Clear, 12-16 hours apart, sanding the first with #600.
Which thinner should I use?
MRF Thinner 3834, at 18-20%.
Can I use it outdoors?
It is made for indoor wood. For outdoor wood, use EezeeWood XT.
How does it compare with MRF’s two-pack wood finishes?
EezeeWood is simpler to use because there is no hardener. For a two-pack PU finish indoors, see FreshWood Interior or WoodCoat Italia; for a water-based, low-odour option, see AquaCoat PU 1K.
Where can I buy it?
Through authorised MRF Paints dealers. Use the MRF Paints dealer locator.
Specifications
| Type | Single-pack solvent-based polyurethane clear wood finish |
|---|---|
| Recommended use | Interior and exterior wood |
| Finish | Clear, glossy or matt |
| Recoat interval | 12-16 hours |
| Thinning | 18-20% |
| Pack sizes | 1 L, 4 L, 20 L, 200 ml, 500 ml |
Coverage depends on surface texture and application method; figures are from the MRF technical data sheet. Download the data sheet (PDF).
16 prime Colour Palette
Brush up on our blogs!
September 16, 2026
Colours That Bring Warmth and Light to Your Home This Monsoon
READ ARTICLE
September 16, 2026
How to Paint a Metal Door: A Step-by-Step Guide for a Smooth Finish
READ ARTICLE
September 2, 2026
5 Trending Colours to Paint Old Wooden Furniture
READ ARTICLE
September 2, 2026
New Home Checklist: Colours, Finishes and First Impressions for Your Dream House
READ ARTICLE
August 25, 2026
Matte Black Magic: Why Black Is the Best Colour for Metal Doors and Railings
READ ARTICLEGET IN TOUCH
Fill the form to book a consultation:
